Tài liệu KYOTO PROTOCOL REFERENCE MANUAL ON ACCOUNTING OF EMISSIONS AND ASSIGNED AMOUNT ppt

Tài liệu KYOTO PROTOCOL REFERENCE MANUAL ON ACCOUNTING OF EMISSIONS AND ASSIGNED AMOUNT ppt

Tài liệu KYOTO PROTOCOL REFERENCE MANUAL ON ACCOUNTING OF EMISSIONS AND ASSIGNED AMOUNT ppt

... commitment. 121 APPENDICES UNFCCC KYOTO PROTOCOL REFERENCE MANUAL ON ACCOUNTING OF EMISSIONS AND ASSIGNED AMOUNT AAU assigned amount unit AR afforestation and reforestation AQAR accounting quantity for afforestation and reforestation AQD ... paragraphs 6 and 7 Decision 13/CMP.1, annex, paragraphs 25 and 32 103 VIII.LAND USE, LAND-USE CHANGE AND FORESTR...

Ngày tải lên: 18/02/2014, 01:20

130 737 0
Tài liệu ARM Architecture Reference Manual- P1 doc

Tài liệu ARM Architecture Reference Manual- P1 doc

... contents of this manual, then lists the conventions and terminology it uses. • About this manual on page iv • Architecture versions and variants on page v • Using this manual on page x • Conventions ... condition field. One value of this field specifies that the instruction is executed unconditionally. Fourteen other values specify conditional execution of the instructi...

Ngày tải lên: 24/12/2013, 19:15

30 354 0
Tài liệu ARM Architecture Reference Manual- P2 docx

Tài liệu ARM Architecture Reference Manual- P2 docx

... Extension. In architecture versions prior to version 5, and in non-E variants of architecture version 5 and above, bit[27] of the CPSR and SPSRs should be treated as described in Other bits on page ... ( SBZ ) on ARM architecture version 3 and below, and on non-T variants of ARM architecture version 4. No instructions exist in these architectures that can switch between...

Ngày tải lên: 24/12/2013, 19:15

30 381 0
Tài liệu DSP Builder Reference Manual ppt

Tài liệu DSP Builder Reference Manual ppt

... the direction using the direction input. Use Enable Port On or Off Turn on to use the clock enable input (ena). Use asynchronous Clear Port On or Off Turn on to enable the asynchronous clear ... or unsigned) of each input and output port in the hardware design. Export On or Off When on, the selected port is exported on an FPGA pin (or on multiple pins for buses). When o...

Ngày tải lên: 19/01/2014, 20:20

30 513 2
Tài liệu ARM Architecture Reference Manual- P3 pptx

Tài liệu ARM Architecture Reference Manual- P3 pptx

... irrespective of the value of the condition code flags. The absence of a condition code on an instruction mnemonic implies the AL condition code. 3.2.1 Condition code 0b1111 As indicated in Table 3-1 on ... mnemonic extension for this condition was NV. Note Use of this condition is now obsolete and unsupported. • In ARM architecture version 3 and version 4, any instruction w...

Ngày tải lên: 22/01/2014, 00:20

30 585 0
Tài liệu ARM Architecture Reference Manual- P4 docx

Tài liệu ARM Architecture Reference Manual- P4 docx

... instruction to bits{25:2] of the byte offset, and the H bit of the instruction to bit[1] of the byte offset. Notes Condition Unlike most other ARM instructions, this instruction cannot be executed conditionally. Bit[24] ... <shifter_operand> where: <cond> Is the condition under which the instruction is executed. The conditions are defined in The condition field on page...

Ngày tải lên: 22/01/2014, 00:20

30 625 1
Tài liệu ARM Architecture Reference Manual- P5 pptx

Tài liệu ARM Architecture Reference Manual- P5 pptx

... <cond> Is the condition under which the instruction is executed. The conditions are defined in The condition field on page A3-5. If <cond> is omitted, the AL (always) condition is ... <cond> Is the condition under which the instruction is executed. The conditions are defined in The condition field on page A3-5. If <cond> is omitted, the AL (always) condition is...

Ngày tải lên: 22/01/2014, 00:20

30 490 0
Tài liệu ARM Architecture Reference Manual- P6 doc

Tài liệu ARM Architecture Reference Manual- P6 doc

... instruction is executed. The conditions are defined in The condition field on page A3-5. If <cond> is omitted, the AL (always) condition is used. <fields> Is a sequence of one or more of ... <Rs> where: <cond> Is the condition under which the instruction is executed. The conditions are defined in The condition field on page A3-5. If <cond> is omitted,...

Ngày tải lên: 22/01/2014, 00:20

30 1,1K 0
Tài liệu ARM Architecture Reference Manual- P7 doc

Tài liệu ARM Architecture Reference Manual- P7 doc

... <cond> Is the condition under which the instruction is executed. The conditions are defined in The condition field on page A3-5. If <cond> is omitted, the AL (always) condition is ... the instruction set on page A3-27 to determine which instruction it is. Architecture version All Exceptions None Operation if ConditionPassed(cond) then alu_out = Rn EOR shifter_operand N Fl...

Ngày tải lên: 22/01/2014, 00:20

30 409 0
Tài liệu ARM Architecture Reference Manual- P8 ppt

Tài liệu ARM Architecture Reference Manual- P8 ppt

... The conditions are defined in The condition field on page A3-5. If <cond> is omitted, the AL (always) condition is used. S Causes the S bit (bit[20]) in the instruction to be set to 1 and ... termination, it must be implemented on the value of the <Rs> operand. The type of early termination used (signed or unsigned) is IMPLEMENTATION DEFINED. C and V flags The UMULL...

Ngày tải lên: 22/01/2014, 00:20

30 390 0
w