Tài liệu PUMP HOUSING CREATED USING SURFACE Pro/ENGINEER doc

... shown in the figure below. 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN PUMP HOUSING CREATED USING SURFACE Pro/ENGINEER Wildfire 2.0 Dr. Herli Surjanhata 20 21 ... *What would cause a surface merge to not be created? Pro/ENGINEER will be unable to create a surface merge if the selected quilts do not actually intersect. Verify that the surface...

Ngày tải lên: 25/01/2014, 06:24

... DataAdapter class by using the TableAdapter Configuration Wizard. To add a bit of variation, rather than setting the DataSource and DataMember properties of the DataGridView control by using the Design ... show you how to update data. First, however, we need to consider some potential problems and how using a DataSet can overcome them. Databases are intended to support multiple conc...

Ngày tải lên: 15/12/2013, 00:15

... Attia, John Okyere. “Matlab Fundamentals.” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere Attia Boca Raton: CRC Press LLC, 1999 ... COMPLEX NUMBERS MATLAB allows operations involving complex numbers. Complex numbers are entered using function i or j. For example, a number zj =+ 22 may be entered in MATLAB as z = 2+2*i ... vector t2. A...

Ngày tải lên: 22/12/2013, 19:17

Ngày tải lên: 17/01/2014, 09:20

... CRC Press LLC Solution Using voltage division V V s sC RsC IN 11 11 1 1 () = + (11.26) From Equation (11.24) V V s R sC O 1 2 2 1 1 () =+ (11.27) Using Equations (11.26 ) ... 11.11. Z 2 Z 1 I 1 V o V a V in Z in A Figure 11.11 Non-Inverting Configuration Using nodal analysis at node A V Z VV Z I aaO 12 1 0 + − += (11.22) From the concept of a ....

Ngày tải lên: 19/01/2014, 17:20

... converting the circuits into the frequency domain and by using the Kirchoff voltage and current laws. The un- known voltages and currents are solved using matrix techniques. Given a network function ... V 4 -j2.5 j8 10 j5 6 -j10V c 2 75 o V I 2 Figure 6.4 Frequency Domain Equivalent of Figure 6.3 Using loop analysis, we have −∠ + − + + − − = 50 4 25 6 5 10 0 0 112 (.)(...

Ngày tải lên: 19/01/2014, 17:20

... diff1(t,y) is created to evaluate % the differential equation % Its m-file is diff1.m % % Transient analysis of RC circuit using ode % function and analytical solution % numerical solution using ... is then solved in the s-domain. By using an inverse Laplace transform, the solution can be expressed in the time domain. We will illustrate this method using Example 5.5 © 199...

Ngày tải lên: 19/01/2014, 17:20

... VVV b =− 14 (4.31) Using Ohm’s Law I VV a = − 43 5 (4.32) Using KCL at node 1, and supernode 1-2, we get VVV V VV b 114 23 210 5 8 0 + − −+ − = (4.33) Using Equation (4.31), ... + + − = () () Using Equation (4.26), the above expression simplifies to −+−= 16 41 6 5 123 III (4.28) For loop 3, 10 8 4 6 0 33 32 III II S +− + −= () Using Equatio...

Ngày tải lên: 19/01/2014, 17:20

... 1999 CRC Press LLC Attia, John Okyere. “Control Statements .” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere Attia Boca Raton: CRC Press LLC, 1999 ... Write a MATLAB program to convert analog signal x to digital signal y. Test the program by using an analog signal with the following amplitudes: -1.25, 2.57 and 6.0. Solution MATLAB

Ngày tải lên: 19/01/2014, 17:20

... B BB = + 2 12 (12.24) RRR BBB = 12 (12.25) Using Kirchoff’s Voltage Law for the base circuit, we have VIRVIR BB B B BE E E =++ (12.26) Using Equation (12.18) and Figure 12.6b, we have ... the stability factors are calculated using Equations (12.37), (12.39), (12,48) and (12.49). The changes in V BE and I CBO with temperature are obtained using Equations (12.32) and...

Ngày tải lên: 25/01/2014, 12:20