Tài liệu Configuring Floating Static Routes pdf

... 5: Advanced Routing v2.0 - Lab 3.6.4 Copyright  2001, Cisco Systems, Inc. 3.6.4: Configuring Floating Static Routes Host A 10.0.0.11 /8 Host B 192.168.3.2 /24 Fa0/0 192.168.3.1 /24 S0/1 192.168.2.1 ... has two routes to the 10.0.0.0/8 network, but only one of these routes is advertised by RIP. If you configure the other path statically, using the default administrative dist...

Ngày tải lên: 24/01/2014, 19:20

... 5: Advanced Routing v2.0 - Lab 3.6.4 Copyright  2001, Cisco Systems, Inc. 3.6.4: Configuring Floating Static Routes Host A 10.0.0.11 /8 Host B 192.168.3.2 /24 Fa0/0 192.168.3.1 /24 S0/1 192.168.2.1 ... has two routes to the 10.0.0.0/8 network, but only one of these routes is advertised by RIP. If you configure the other path statically, using the default administrative dist...

Ngày tải lên: 24/01/2014, 19:20

... and test its ability to install alternate routes in the event of link failure. Step 1 Build and configure the network according to the diagram, configuring EIGRP as indicated for AS 100. ... - 3 Semester 5: Advanced Routing v2.0 - Lab 6.7.2 Copyright  2001, Cisco Systems, Inc. 6.7.2 Configuring EIGRP Fault Tolerance Fa0/0 192.168.72.1 /24 S0/1 192.168.64.6 /30 S0/0 192.168.6...

Ngày tải lên: 11/12/2013, 15:15

... Lefkovics, MCSE, A+ William C. Wade III, MCSE, MCT WIN A PALM Vx ! DETAILS ON BACK EXCHANGE 2000 SERVER CONFIGURING “The ultimate resource for managing Exchange 2000 in the enterprise. This book contains ... used. The higher the cost, the less likely a site link will be selected when there are multiple routes to the same desti- nation. To create a site link: 1. In the Active Directory S...

Ngày tải lên: 21/12/2013, 05:17

... restriction is that the paths must have the same cost. Configuring OSPF Configuring OSPF is slightly different from configuring RIP or IGRP. When configuring OSPF, use the following syntax: Router(config)# ... view the EIGRP routes in your router’s routing table, use the show ip route command: Router# show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, 30 Chapter 11:...

Ngày tải lên: 18/01/2014, 04:20

... CCNA 4: WAN Technologies v 3.0 - Lab 5.2.2 Copyright  2003, Cisco Systems, Inc. Lab 5.2.2 Configuring Frame Relay PVC Objective • Configure two routers back-to-back as a Frame Relay ... problem completing this, refer to the Network Address Translation (NAT) configuration lab. Step 2 Configuring the serial interface First, define the Frame Relay frame type to be used on this l...

Ngày tải lên: 18/01/2014, 05:20

... Lab 5.2.3 Configuring Frame-Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame ... ___________________________________________________ c. If not, troubleshoot the routers configurations. d. List the IGRP routes ___________________ ___________________ ___________________ Step 11 Verify connectivity

Ngày tải lên: 18/01/2014, 05:20

... Configuration Task List – Configuring a Tunnel Server to Request Dial-Out – Configuring an NAS to Accept Dial-Out • Advanced VPN Configuration Task List – Configuring per-User VPN – Configuring Preservation ... remote router that is being dialed. Configuring Virtual Private Networks Configuring VPN DNC-166 Cisco IOS Dial Services Configuration Guide: Network Services Configuring...

Ngày tải lên: 24/01/2014, 10:20

... 3 Semester 5: Advanced Routing v2.0 - Lab 5.8.4 Copyright  2001, Cisco Systems, Inc. 5.8.4: Configuring Virtual Links TRANSIT AREA 51 AREA 3 AREA 0 Lo0 192.168.3.1 /24 S0/1 192.168.240.1 ... noticed already, but he proudly says that he has added OSPF Area 3 in Auckland so that external routes do not need be redistributed. You agree that it would be best to include Auckland in the .....

Ngày tải lên: 11/12/2013, 15:15

... Lab 3.3.2 Configuring PPP Encapsulation Objective • Configure the serial interfaces on two routers with

Ngày tải lên: 11/12/2013, 15:15