Tài liệu Configuring Floating Static Routes pptx

... 5: Advanced Routing v2.0 - Lab 3.6.4 Copyright  2001, Cisco Systems, Inc. 3.6.4: Configuring Floating Static Routes Host A 10.0.0.11 /8 Host B 192.168.3.2 /24 Fa0/0 192.168.3.1 /24 S0/1 192.168.2.1 ... has two routes to the 10.0.0.0/8 network, but only one of these routes is advertised by RIP. If you configure the other path statically, using the default administrative dist...

Ngày tải lên: 24/01/2014, 19:20

... 5: Advanced Routing v2.0 - Lab 3.6.4 Copyright  2001, Cisco Systems, Inc. 3.6.4: Configuring Floating Static Routes Host A 10.0.0.11 /8 Host B 192.168.3.2 /24 Fa0/0 192.168.3.1 /24 S0/1 192.168.2.1 ... has two routes to the 10.0.0.0/8 network, but only one of these routes is advertised by RIP. If you configure the other path statically, using the default administrative dist...

Ngày tải lên: 24/01/2014, 19:20

... CCNA 4: WAN Technologies v 3.0 - Lab 5.2.5 Copyright  2003, Cisco Systems, Inc. Lab 5.2.5 Configuring Frame Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame ... interfaces according to the chart If problems occur during this configuration, refer to Lab 1.1.4a Configuring NAT. Step 2 Configure the Serial 0 Interfaces a. First, the Frame Relay encaps...

Ngày tải lên: 18/01/2014, 05:20

... following sections: • Configuring MPLS Levels of Control • Configuring MPLS Traffic Engineering • Configuring MPLS Traffic Engineering Paths • Configuring MPLS Virtual Private Networks • Configuring MPLS ... on the PE to CE link. Configuring Multiprotocol Label Switching Configuring MPLS Virtual Private Networks XC-87 Cisco IOS Switching Services Configuration Guide Configuring...

Ngày tải lên: 24/01/2014, 10:20

... Rules 395 The WLBS Command Line Utility 398 Configuring Network Load Balancing 399 Configuring Cluster Parameters 400 Configuring Host Parameters 402 Configuring Port Rules 402 Monitoring and Administering ... PLAN WITHOUT Active Directory Configuring Windows 2000 Carol Bailey Tom Shinder Technical Editor Make the Most of Windows 2000 WITHOUT Active Directory • Step-by-Step Instruct...

Ngày tải lên: 21/12/2013, 06:15

... Downloadable HTML FREE Membership to Access.Globalknowledge ARCHITECTURE FOR VOICE, VIDEO, AND INTEGRATED DATA CONFIGURING CISCO ® AVVID 94_FC.qx 1/18/01 3:06 PM Page 1 Configuring Cisco CallManager • Chapter

Ngày tải lên: 21/12/2013, 06:16

... link, you decide to use a static route. Auckland is a stub network. It has only one exit point to the rest of the world. In this situation, you can configure a static default route that will ... features to optimize routing. These features include distribute lists, passive interfaces, default routes, and route redistribution. Scenario International Travel Agency (ITA) uses RIP...

Ngày tải lên: 21/12/2013, 19:15

... your supplied executable to easily connect to your remote access services.You can use either a static phone book to supply the actual connection details or a dynamic phone book that the user

Ngày tải lên: 23/12/2013, 01:16

... - 3 Semester 5: Advanced Routing v2.0 - Lab 3.6.2 Copyright  2001, Cisco Systems, Inc. 3.6.2: Configuring IGRP Host B 192.168.3.2 /24 Fa0/0 192.168.3.1 /24 S0/1 192.168.2.1 /24 S0/0 192.168.1.1 ... settings. Use the show ip route command to verify that the routers are installing two unequal-cost routes to the same destination: Vista#show ip route <output omitted> I 10.0....

Ngày tải lên: 24/01/2014, 19:20

... (loopback 0). Unless you are using IOS version 12.1, RIP automatically propagates statically defined default routes. So, depending on your IOS version, you might need to explicitly configure ... currently uses RIP. The company connects to the Internet via SanJose2, so you decide to configure a static default route on that router. Then you must configure RIP so that it will propagate...

Ngày tải lên: 24/01/2014, 19:20