Tài liệu Lab 9 2 5 VTP Client and Server Configurations doc

... Basics and Intermediate Routing v 3.0 - Lab 9. 2. 5 Copyright  20 03, Cisco Systems, Inc. Lab 9. 2. 5 VTP Client and Server Configurations Objective • Create a basic switch configuration and ... starting with an unconfigured switch. Instructions are provided for the 29 0 0, 29 5 0, and 190 0 Series switches. 29 0 0 and 29 5 0 Series Switches 1....

Ngày tải lên: 24/01/2014, 19:20

... Lab 9. 2. 5 VTP Client and Server Configurations Objective • Create a basic switch configuration and verify it. • Create multiple VLANs, name them and assign multiple member ... typing exit, and turn all the devices off. Then remove and store the cables and adapter. 5 - 6 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 9. 2. 5 Copyrigh...

Ngày tải lên: 16/10/2013, 21:15

... Addresses 199 .99 .9. 32/ 27 have been allocated for Internet access outside of the company. Use the ip route command to create the static route: ISP(config)#ip route 1 72. 16. 12. 0 25 5 . 25 5 . 25 5. 0 1 72. 16.1.6 ... commands: campus(config)#ip dhcp pool campus campus(dhcp-config)#network 1 72. 16. 12. 0 25 5 . 25 5 . 25 5. 0 campus(dhcp-config)#default-router 1 72....

Ngày tải lên: 11/12/2013, 13:15

... GAD from a class B ( 25 5 . 25 5. 0.0) to a Class C ( 25 5 . 25 5 . 25 5. 0). Use the same IP address. GAD(config)#interface fastethernet 0 GAD(config-if)#ip address 1 72. 16.0.1 25 5 . 25 5 . 25 5. 0 GAD(config-if)#exit ... 0 BHM(config-if)#ip address 1 72. 16.1 .2 255 . 25 5 . 25 5. 0 BHM(config-if)#exit BHM(config)#interface fastethernet 0 BHM(config-if)#ip add...

Ngày tải lên: 11/12/2013, 13:15

... router 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1 .2. 5 Copyright  20 03, Cisco Systems, Inc. Step 1 Identify connectors and components a. Examine the router and locate the RJ- 45 connector ... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1 .2. 5 Copyright  20 03, Cisco Systems, Inc. Lab 1 .2. 5 Connecting Console Interfaces Object...

Ngày tải lên: 11/12/2013, 13:15

... one and doubles, Base 2, for each position to the left. 8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1 Position Value 128 20 7 128 64 79 64 8 15 8 4 7 4 2 3 2 1 The same conversion table and ... cannot be divided by either 32 or 16, put 0s in row three of our table under the 32 and 16 values. 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 1 .2. 5 Copyr...

Ngày tải lên: 11/12/2013, 13:15

... GAD from a class B ( 25 5 . 25 5. 0.0) to a Class C ( 25 5 . 25 5 . 25 5. 0). Use the same IP address. GAD(config)#interface fastEthernet 0 GAD(config-if)#ip address 1 72. 16.0.1 25 5 . 25 5 . 25 5. 0 GAD(config-if)#exit ... BHM(config-if)#ip address 1 72. 16.3.1 25 5 . 25 5 . 25 5. 0 BHM(config-if)#exit BHM(config)#exit b. On the GAD router: GAD(config)#interfac...

Ngày tải lên: 11/12/2013, 13:15

... Identify connectors and components a. Examine the router and locate the RJ 45 connector labeled “Console”. 2 - 3 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1 .2. 5 Copyright  20 03, Cisco Systems, ... 1 - 3 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1 .2. 5 Copyright  20 03, Cisco Systems, Inc. Lab 1 .2. 5 Connecting Console Interfaces Objective...

Ngày tải lên: 11/12/2013, 13:15

... the remainder cannot be divided by either 32 or 16, put 0s in row three of our table under the 32 and 16 values. 128 20 7 128 64 79 64 8 15 8 4 7 4 2 3 2 1 Position Value ... The value row starts with one and doubles, base 2, for each position to the left. 8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1 The same conversion table and simple division can be...

Ngày tải lên: 11/12/2013, 13:15

... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 10 .2. 5 Copyright  20 03, Cisco Systems, Inc. Lab 10 .2. 5 Well-Known Port Numbers and Multiple Sessions Objective ... session lab. Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. 2 - 5 CCNA 2: Routers...

Ngày tải lên: 11/12/2013, 14:15