... Router 1 GAD DCE 19 2 .16 8. 15 . 1 255 . 255 . 255 .0 class cisco Router 2 BHM DTE 19 2 .16 8. 15 . 2 255 . 255 . 255 .0 class cisco 2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1 .5 Copyright ... GAD(config)#interface serial 0 GAD(config-if)#ip address 19 2 .16 8. 15 . 1 255 . 255 . 255 .0 GAD(config-if)#clock rate 56 000 GAD(config-if)#no shutd...
Ngày tải lên: 11/12/2013, 13:15
... 1 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1 .5 Copyright 2003, Cisco Systems, Inc. Battery Lab 3 .1 .5 Series Circuits Switch Bulb ... LEDs with resistors • 6v lantern battery 2 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1 .5 Copyright 2003, Cisco Systems, Inc. Step 1 Measure the Resistances of all devices Measure the ... have one multimeter a...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.5 Configuring a Serial Interface ppt
... Router 1 GAD DCE 19 2 .16 8. 15 . 1 255 . 255 . 255 .0 class cisco Router 2 BHM DTE 19 2 .16 8. 15 . 2 255 . 255 . 255 .0 class cisco 2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1 .5 Copyright ... GAD(config)#interface serial 0 GAD(config-if)#ip address 19 2 .16 8. 15 . 1 255 . 255 . 255 .0 GAD(config-if)#clock rate 56 000 GAD(config-if)#no shutd...
Ngày tải lên: 18/01/2014, 04:20
Tài liệu Lab 3.1.7 Troubleshooting a Serial Interface doc
... follows: London(config)#interface serial 0 London(config-if)#ip address 19 2 .16 8. 15 . 1 255 . 255 . 255 .0 London(config-if)#no shutdown London(config-if)#exit London(config)#exit Step 4 Save the ... functioning by pinging the serial interface of the other router London#ping 19 2 .16 8. 15 . 2 Paris#ping 19 2 .16 8. 15 . 1 a. From London, can you ping the Paris...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface docx
... router. GAD(config)#interface fastEthernet 0 GAD(config-if)#ip address 19 2 .16 8 .14 .1 255 . 255 . 255 .0 GAD(config-if)#no shutdown GAD(config-if)#exit GAD (config)#exit Note: Once interface configuration ... 800, 16 00, 17 00, 250 0, 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 10.1.6 Multiple Active Host Sessions doc
... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 10 .1. 6 Copyright 2003, Cisco Systems, Inc. Lab 10 .1. 6 Multiple Active Host Sessions Objective ... this lab. Perform those steps on all routers in this lab assignment before continuing. 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 10 .1. 6 Copyright 2003, Cisco Systems, Inc. Step 1 ... interface ident...
Ngày tải lên: 11/12/2013, 14:15
Tài liệu Lab 5.1.4 RJ-45 Jack Punch Down docx
... 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 5. 1. 4 Copyright 2003, Cisco Systems, Inc. Lab 5. 1. 4 RJ- 45 Jack Punch Down Objective • Learn the correct process for terminating or punching ... inside the jack. The punch tool also cuts off any extra wire. CAT 5 or CAT 5e cabling and CAT 5 or 5e rated T568-B jacks will be used. A CAT 5/ 5e straight- wired p...
Ngày tải lên: 24/01/2014, 19:20
Tài liệu Lab 5.1.5 RJ-45 Jack Punch Down doc
... Lab 5. 1 .5 RJ- 45 Jack Punch Down Objective • Learn the correct process for terminating or punching down an RJ- 45 jack • Learn the correct procedure for installing the jack in a ... tester. • Category 5/ 5e wall plate • 11 0 type punch- down tool • Wire cutters Use the following procedure and diagram to punch down the wires into the RJ- 45 jack and...
Ngày tải lên: 24/01/2014, 19:20
Tài liệu Lab 7.3.5 Configuring IGRP pptx
... AS 10 1 on BHM. Go to the proper command mode and enter the following: BHM(config)#router igrp 10 1 BHM(config-router)#network 19 2 .16 8. 25. 0 BHM(config-router)#network 19 2 .16 8.22.0 Step 5 ... mode and enter the following: GAD(config)#router igrp 10 1 GAD(config-router)#network 19 2 .16 8.22.0 GAD(config-router)#network 19 2 .16 8.20.0 Step 3 Save the Gadsden...
Ngày tải lên: 11/12/2013, 14:15
Tài liệu Lab 7.3.5 Configuring IGRP ppt
... Enable/VTY/Console passwords Router 1 GAD 19 2 .16 8.20 .1 DCE 19 2 .16 8.22 .1 255 . 255 . 255 .0 class cisco Router 2 BHM 19 2 .16 8. 25. 1 DTE 19 2 .16 8.22.2 255 . 255 . 255 .0 class cisco Objective • Setup ... AS 10 1 on BHM. Go to the proper command mode and enter the following: BHM(config)#router igrp 10 1 BHM(config-router)#network 19 2 .16 8. 25. 0 BHM(conf...
Ngày tải lên: 11/12/2013, 14:15