... 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 5. 1. 4 Copyright 2003, Cisco Systems, Inc. Lab 5. 1. 4 RJ- 45 Jack Punch Down Objective • Learn the correct process for terminating or punching ... inside the jack. The punch tool also cuts off any extra wire. CAT 5 or CAT 5e cabling and CAT 5 or 5e rated T568-B jacks will be used. A CAT 5/ 5e straight- wir...
Ngày tải lên: 24/01/2014, 19:20
... Lab 5. 1 .5 RJ- 45 Jack Punch Down Objective • Learn the correct process for terminating or punching down an RJ- 45 jack • Learn the correct procedure for installing the jack in a ... Two Category 5/ 5e RJ- 45 data jacks (one extra for spare) – If RJ- 45 data jacks are installed on both ends of the cable, the installation can be tested by inserting cable with RJ...
Ngày tải lên: 24/01/2014, 19:20
Tài liệu Lab 5.1.13b Building a Switch-based Network pptx
... Computer IP Address Subnet mask Default Gateway PC – A 19 2 .16 8 .1. 1 255 . 255 . 255 .0 Not Required PC – B 19 2 .16 8 .1. 2 255 . 255 . 255 .0 Not Required Step 5 Access the Command or MS-DOS prompt a. Use the ... 1 - 4 CCNA 1: Networking Basics v 3.0 - Lab 5. 1. 13b Copyright 2003, Cisco Systems, Inc. Lab 5. 1. 13b Building a Switch-based Network Objective...
Ngày tải lên: 11/12/2013, 14:15
Tài liệu Lab 3.1.4 Using Router show Commands pdf
... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 4 Copyright 2003, Cisco Systems, Inc. Lab 3 .1. 4 Using Router show Commands Objective • ... available flash memory and the amount used. Flash is where the Cisco Internetwork Operating System (IOS) file or image is stored. 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 4 Copyright ... 800, 16 0...
Ngày tải lên: 18/01/2014, 04:20
Tài liệu Lab 3.1.4 Using Router show Commands ppt
... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 4 Copyright 2003, Cisco Systems, Inc. Lab 3 .1. 4 Using Router show Commands Objective ... configuration output used in this lab is produced from 17 21 series routers. Any other router used may produce 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 4 Copyright 2003, Cisco Systems, ... 8...
Ngày tải lên: 18/01/2014, 04:20
Tài liệu Lab 5.1.3 Using the Boot System Command pptx
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 5. 1. 3 Copyright 2003, Cisco Systems, Inc. Lab 5. 1. 3 Using the Boot System Command Objective ... 800, 16 00, 17 00, 250 0, 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. ... of the previous ste...
Ngày tải lên: 18/01/2014, 04:20
Tài liệu Lab 5.1.3 Using the Boot System Command doc
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 5. 1. 3 Copyright 2003, Cisco Systems, Inc. Lab 5. 1. 3 Using the Boot System Command Objective ... 800, 16 00, 17 00, 250 0 and 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. ... secret pa...
Ngày tải lên: 18/01/2014, 04:20
Tài liệu Lab 5.1.3 Connecting Router LAN Interfaces pdf
... • One router with an RJ- 45 Ethernet or Fast Ethernet interface or an AUI interface • 10 BASE-T AUI transceiver (DB 15 to RJ 45 ) for a router with an AUI Ethernet interface ( 250 0 Series) • Several ... 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 5. 1. 3 Copyright 2003, Cisco Systems, Inc. Lab 5. 1. 3 Connecting Router LAN Interfaces ... Locate one or more R...
Ngày tải lên: 24/01/2014, 19:20
Tài liệu Lab 5.1.5 Troubleshooting Configuration Register Boot Problems doc
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 5. 1 .5 Copyright 2003, Cisco Systems, Inc. Lab 5. 1 .5 Troubleshooting Configuration Register ... the config-register 0x 210 2. Upon completion of the previous steps, logoff by typing exit. Turn the router off. 4 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 5. 1 .5 Copyright 2003, ... Router>...
Ngày tải lên: 24/01/2014, 19:20
Tài liệu Activity 5.1: Risks of Skipping Logical Design docx
... Activity 5. 1: Risks of Skipping Logical Design In this activity, you will participate in a class discussion ... activity. Materials There are no materials for this activity. Time to complete this activity: 10 minutes.
Ngày tải lên: 10/12/2013, 16:16