Tài liệu Lab 1 1 2 PC Hardware doc

... / Characteristics 1. 2. 3. 4. 5. Step 2 Remove the PC system unit cover and examine internal components 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 1. 1 .2 Copyright  20 03, Cisco Systems, ... Lab 1. 1 .2 PC Hardware Objective • Become familiar with the basic peripheral components of a PC computer system. • Identify PC connections including network ......

Ngày tải lên: 24/01/2014, 19:20

... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 2 Copyright  20 03, Cisco Systems, Inc. Lab 3 .1. 2 Command Modes and Router Identification ... 800, 16 00, 17 00, 25 00, 26 00 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. ... ________________...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 2 Copyright  20 03, Cisco Systems, Inc. Lab 3 .1. 2 Voltage Measurement Objective • Demonstrate ... approximately 12 0 volts of AC directly to any electrical appliance that is plugged in. Examples of appliances are a computer, 2 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 2 Copyright  20 03, Cisco ... will...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 2 Copyright  20 03, Cisco Systems, Inc. Lab 3 .1. 2 Command Modes and Router Identification ... 800, 16 00, 17 00, 25 00 and 26 00 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. ... _____________...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9 .1. 2 Copyright  20 03, Cisco Systems, Inc. Lab 9 .1. 2 Gateway of Last Resort Objective • Configure ... 0.0.0.0 0.0.0.0 17 2 .17 .0 .2 at the configuration prompt. b. Type show ip route at the privileged exec mode. 3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9 .1. 2 Copyright  20 03, Cisco Systems...

Ngày tải lên: 18/01/2014, 05:20

... password Enable/VTY/Console passwords Router 1 GAD 17 2 .16 .0 .1 DCE 17 2 .17 .0 .1 25 5 .25 5.0.0 class cisco Router 2 BHM 17 2 .18 .0 .1 DTE 17 2 .17 .0 .2 255 .25 5.0.0 class cisco Objective • Configure ... there is a problem 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9 .1. 2 Copyright  20 03, Cisco Systems, Inc. doing this, refer to the C...

Ngày tải lên: 18/01/2014, 05:20

... 1 GAD DCE 19 2 .16 8 .15 .1 25 5 .25 5 .25 5.0 class cisco Router 2 BHM DTE 19 2 .16 8 .15 .2 255 .25 5 .25 5.0 class cisco 2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 5 Copyright  20 03, ... __________________________________________________________________________ Step 10 Verify that the serial connection is functioning a. ping the serial...

Ngày tải lên: 11/12/2013, 13:15

... 1 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright  20 03, Cisco Systems, Inc. Battery Lab 3 .1. 5 Series Circuits Switch Bulb ... bases or LEDs with resistors • 6v lantern battery 2 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright  20 03, Cisco Systems, Inc. Step 1 Measure the Resistances of all devices Measure ... have one multimet...

Ngày tải lên: 11/12/2013, 13:15

... password Enable/VTY/Console passwords Gadsden 17 2 .16 .0 .1 25 5 .25 5.0.0 Cisco1 3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright  20 03, Cisco Systems, Inc. b. To change information, ... Refer to interface chart. GAD(config)#interface Serial 0 GAD(config-if)#ip address 19 2 .16 8 .14 .1 25 5 .25 5 .25 5.0 GAD(config-if)#no shutdown GAD(...

Ngày tải lên: 11/12/2013, 13:15

... 0 Address Subnet mask Enable Secret password Enable/VTY/Console passwords GAD 19 2 .16 8 .14 .1 25 5 .25 5 .25 5.0 class cisco Objective • Configure some basic router settings. • Bring interfaces ... Refer to interface chart. GAD(config)#interface Serial 0 GAD(config-if)#ip address 19 2 .16 8 .14 .1 25 5 .25 5 .25 5.0 GAD(config-if)#no shutdown GAD(config-if)#descri...

Ngày tải lên: 11/12/2013, 13:15