Tài liệu Lab Scenario 1 -- Frame Relay and OSPF pdf
Tài liệu Lab Scenario 1 -- Frame Relay and OSPF pdf
... routed
6d21h: IP: local to Serial0 13 5.6 .1. 1
6d21h: IP: s =13 5.6 .1. 4 (Serial0), d =13 5.6 .1. 1 (Serial0), len 10 0,
policy rejected normal forwarding
6d21h: IP: s =13 5.6 .1. 1 (local), d =13 5.6 .1. 4, len 10 0, ... routed
6d21h: IP: local to Serial0 13 5.6 .1. 1
6d21h: IP: s =13 5.6 .1. 4 (Serial0), d =13 5.6 .1. 1 (Serial0), len 10 0,
policy rejected normal forwarding
6d21h:...
Tài liệu Lab Exercise 1: VLAN, Trunk, and EtherChannel Configuration pptx
... 2 and 3.
e. Place the ports connected to PC -1 and the router in the appropriate VLANs. Did this work? Why or
why not?
Device IP Addresses
Switch A 10 .1. 1 .1/ 24
Switch B 10 .1. 1.2/24
PC -1 10.2 .1. 1/24
PC-2 ... 10 .2 .1. 1/24
PC-2 10 .2 .1. 2/24
PC-3 10 .3 .1. 2/24
Router 10 .3 .1. 1/24
CertificationZone Page 3 of 4
http://www.certificationzone.com/studyguides /?Issue=36&...
Tài liệu Lab 3.1.1 Safe Handling and Use of a Multimeter docx
...
Lab 3 .1. 1 Safe Handling and Use of a Multimeter
Objective
• Learn how to use and handle a multimeter correctly.
Background
A multimeter ... not drop it or handle it
carelessly. Be careful not to accidentally nick or cut the red or black wire leads, called probes.
1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 1 Copyright 2003, ...
• A digital multimeter. A Fluke...
Tài liệu Lab 3.1.1 Safe Handling and Use of a Multimeter doc
...
Lab 3 .1. 1 Safe Handling and Use of a Multimeter
Objective
• Learn how to use and handle a multimeter correctly.
Background
A multimeter ... not drop it or handle it
carelessly. Be careful not to accidentally nick or cut the red or black wire leads, called probes.
1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 1 Copyright 2003, ...
• A digital multimeter. A Fluke...
Tài liệu Lab 3.1.2 Command Modes and Router Identification docx
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 2 Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 2 Command Modes and Router Identification
Objective ... Establishing a HyperTerminal session lab.
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps before
continuing with this lab.
Step 1 Login to the router in user ... 8...
Tài liệu Lab 3.1.2 Command Modes and Router Identification doc
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 2 Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 2 Command Modes and Router Identification
Objective ... 800, 16 00,
17 00, 2500 and 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly
identify the interface identifiers to be used based on the equipment in the lab. ... Esta...
Tài liệu Cisco Voice Over Frame Relay, ATM, and IP pptx
... 9E0-423 11
Q 31.
What command allows you to expand the dialed digits 12 34 to include a 1 and the 510 area code?
A. num-exp 12 34 15 1 012 34
B. exp-num 12 34 15 1 012 34
C. expand 12 34 15 1 012 34 ... calculating the total bandwidth necessary for data PVCs?
A. 1. 13
B. 1. 23
C. 1. 33
Answer: A.
Q98.
What is the speed or bandwidth of a T1?
A....
Tài liệu Lab 3.1.5 Configuring a Serial Interface pptx
...
Router 1
GAD
DCE 19 2 .16 8 .15 .1 255.255.255.0 class cisco
Router 2
BHM
DTE 19 2 .16 8 .15 .2 255.255.255.0 class cisco
2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 5 Copyright ... connection is functioning
a. ping the serial interface of the other router.
BHM#ping 19 2 .16 8 .15 .1
GAD#ping 19 2 .16 8 .15 .2
b. From GAD, ping the BHM route...
Tài liệu Lab 3.1.5 Series Circuits docx
... 1 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright 2003, Cisco Systems, Inc.
Battery
Lab 3 .1. 5 Series Circuits
Switch
Bulb
... terminology and concepts of networking. This lab also helps increase the overall
understanding of some of the basic electrical circuit building blocks.
Prior to starting the lab, the teacher or lab ... have one multimeter...
Tài liệu Lab 3.1.6 Making Configuration Changes doc
...
17 2 .16 .0 .1 255.255.0.0 Cisco1
3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc.
b. To change information, go to the proper command mode and ... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 6 Making Configuration Changes
Objective ... session lab....