ToshibaCopiers Most devices Toshiba (at least those that are not counterparts Sharp'ov) error codes and setup procedures are the same in so far as they are inherent in these models (this is the fact that 15hh are unusual, for example, error-duplex) Lit key, what to do? Simultaneously press the [Stop] and [8], to see the display, look at the error codes to determine the cause of the key The reset after eliminating need only stove error (mode +8, code 89, error counter reset), other errors are reset elimination reasons Enter the service mode: Turn on the machine while pressing the button: + + or diagnostic mode 0+5 adjustment mode 0+6 Forced mode readiness 0+7 Run mode 8+0 Setting Mode To exit the service mode, you can press +9 or just turn off and turn on the machine The installation procedure of the developer for the majority of those around us copiers proprietary Toshiba is one: Mode + code 0, wait for the display "24" (or "245" for cars with a three-digit indication of the process), a sign of the end of the procedure - "turned green" indicator on the [print] and the desired display on a digital display; Record result Button [interrupt] ([=] arrow inside), if available, or the [print] button when [interrupt] there or [Stop] if you press [Print] does not stop the process "Sunshine" and "key": Entrance to the service: C - Auto / text / photo - C - Auto / text / photo E-studio Toshiba 24-06 - Reset counter developer 12/15/120/150 20-01 - Reset counter THEN Toshiba e-studio 161 Entrance to the service: C - Auto / text / photo - C - Auto / text / photo 20-01 - Reset counter THEN 42-01 - Reset counter developer 24-07 - Reset the photoconductor counter (for replacement) E-studio Toshiba Resetting the drum counter 08 + on - 673 - set 16/20/25/160 on the machine e-studio 16/20/25 steps for the Modification of the 200/250 development unit PU-1600ES (SRU) and set 08-689 Reset oven error: E-studio Toshiba 12/15/120/150/161 Error code: H2, H3, H4 included in the service: C - Auto / text / photo - C - Auto / text / photo Enter 14, then "Start" Error Code: C41, C43, C44, C45 Toshiba e-studio Press 08 + on - enter the 400, to reset the value to stand 16 / 25series / 160 / there; storing values - key SET or START to Model E250series / 163 / 203series / 16/160/20/200 for the Model E-163/203/230/232/280 click 230/280 series Interrupt Repeat for inexperienced users: Never use any other diagnostic codes and procedures, because it can lead to unpredictable consequences Bear in mind that resetting the drum counter does not guarantee you from all the other troubles, so at the first opportunity brought copier service firm to practicing it removed, cleaned and made the necessary adjustments Error Codes Most models of the error codes are the same, but it would be better to see a more detailed list of specific models Toshiba Online StartCopy A1 Charge corona cleaner problem A2 ADD problem A4 Sorter problem A5 Board problem A6 Sorter board problem A7 ADF interface A0 Communication problem between main board and PFC C1-C3 C01 Main motor drive problem C4 C04 Pedestal main drive problem C05 Duplex drive problem C11 Duplex exit motor C12 Duplex end motor C13 Upper cassette C14 Lower cassette C15 Pedestal upper cassette C16 Pedestal middle cassette C17 Pedestal lower cassette C18 LCT C21 Scan problem C22 Lens problem C23 Mirror motor C26 Exposure lamp C27 Scan motor will not shut off C33 Set up failure C35 Developer at transfer / separator adjustment This might mean a developer C8 leak or shorted corona C7 C41 Fuser thermistor or low temperature C43 Fuser problem after warm-up C44 Fuser problem after warm-up C45 Fuser sub-thermistor open User problems Reset required Turn off power Hold "0" & "8" keys while turning power on Then press "8" Then press "9" Then press "print" You will read "3" in the display Using the # keys, press "0" & "9" at the same time C5 Optics locked or not initialized Could be scan or lens / mirror C6 Home sensor CA Main board problem CB ADF feed motor drive problem CC ADF transport motor drive problem CD BC RAM hardware (EEPROM at end of life) CE BC RAM software (EEPROM / main board problem) CF DV unit out or toner sensor problem CP Drive problem (Motor lock) E0 Waste toner full E1 E01 Jam E2 E02 Fuser jam E3 E03 Jam at turn on E4 E04 Front door opened during copy cycle E5 E05 Paper feed jam from lower cassette E6 E8 Paper feed jam from upper cassette E08 E9 Duplex unit jam Jam in pedestal E11 Duplex jam E12 Bypass jam E13 Upper cassette jam E14 2nd cassette jam E15 3rd cassette jam E16 4th cassette jam E17 4th cassette jam E19 CT jam E21 LCT jam E22-E25 Paper jams in copier EC E71 ADF feed jam ED E72 ADF transport jam EE E73 ADF exit jam E74 RADF jam E75 ADF 2nd original jam E81-E85 Sorter jam E88 Jam after sorter ... and made the necessary adjustments Error Codes Most models of the error codes are the same, but it would be better to see a more detailed list of specific models Toshiba Online StartCopy A1 Charge... diagnostic codes and procedures, because it can lead to unpredictable consequences Bear in mind that resetting the drum counter does not guarantee you from all the other troubles, so at the first opportunity... problem after warm-up C44 Fuser problem after warm-up C45 Fuser sub-thermistor open User problems Reset required Turn off power Hold "0" & "8" keys while turning power on Then press "8" Then press