Moldflow 2 Part 9 doc

Add Component 8-23 MoldWorks2006 User Guide 8.10 Angular Pin Create an angular pin with hole(s) through the relevant plates according to the "Oversize" values. Press to see the parameter scheme. Parameters • *D1 - Pin diameter. • D2 - Pin shoulder diameter. • D3 - Pin head diameter. • K - Head length. • A - Head angle (and Pin angle). • N - Head + Shoulder length • L - Total length. Add Component 8.11 Cap Screw Create a cap screw and cap screw hole(s) through the relevant plates according to the "Oversize" values. Press to see the parameter scheme. Pa am use the scroll bar on th ha d s ccess the missing para r eters - e right- n ide to a meters. ter. D2 - Shoulder diameter. • K - Shoulder length. • Tap - Tap length. • DP - Depth of tapping preparation drill (affects the hole only) • S1 - Screw length. • SW - Size of hexagon hole. • B - Actual thread length. • *D1 - Screw diame • • D3 - Diameter of tapping preparation drill. 8-24 MoldWorks2006 User Guide Add Component 8-25 MoldWorks2006 User Guide • Gap - Safety gap. The Through Thread check box will cause the hole to be a through hole on the final part. Add Component 8-26 MoldWorks2006 User Guide w 8.12 Countersunk Scre Create a countersunk screw and countersunk screw hole(s) through the relevant plates according to the "Oversize" values. Parameters - use the scroll bar on the right- hand side to access the missing parameters. • *D1 - Screw diameter. n h. gth. h of tapping preparation ad length. . • D2 - Head diameter. • D3 - Diameter of tapping preparatio drill. • K - Shoulder lengt • Tap - Tap len • DP - Dept drill. • SW - Size of hexagon hole. • B - Actual thre • Gap - Safety gap Add Component 8-27 MoldWorks2006 User Guide A - Socket head angle. hrough hole on . • The Through Thread check box will cause the hole to be a t the final part Add Component 8-28 MoldWorks2006 User Guide 8.13 Shoulder Screw Create a shoulder screw and shoulder screw hole(s) through the relevant plates according to the "Oversize" values. Press to see the parameter scheme. has the parameter Hole Type: 1: This dialogue Hole Type Through hole Parameters - use the scroll bar on the right- hand side to access the missing parameters. • *M - Screw diameter. • d - Screw body diameter. • D - Head diameter. • K - Head Depth. • t - Hole extension from top of head. • S - Movement distance. • T - Thread length. • Tap - Tap depth. Add Component 8-29 MoldWorks2006 User Guide ia eter of taping preparation drill. • SW - Size of hexagon hole. The other two types have the same parameters but the hole does not go through the top plate. ll use the h hole on the final part. • D3 - D m • Dp - Depth of tapping preparation drill. • L - Screw length. Hole Type 3: Blind countersunk hole. Hole Type 2: Blind drill hole. The Through Thread check box wi ca hole to be a throug Add Component 8.14 Set Screw Create a set screw and set screw hole(s) through the relevant plates according to the "Oversize" values. Press to see the parameter scheme. Parameters • • • • *D1 - Screw diameter. D3 - Hole diameter. SW - Key diameter. L - Length. 8-30 MoldWorks2006 User Guide Add Component Click this icon to access the ejector lock dialogue (refer to Ejector Locks). 8-33 MoldWorks2006 User Guide Add Component Click this icon to acces ths e ejector lock dialogue (refer to Ejector Locks). 8-35 MoldWorks2006 User Guide [...]...Add Component Click this icon to access the ejector lock dialogue (refer to Ejector Locks) MoldWorks2006 User Guide 8-37 . 8 -24 MoldWorks2006 User Guide Add Component 8 -25 MoldWorks2006 User Guide • Gap - Safety gap. The Through Thread check box will cause the hole to be a through hole on the final part. . 8 -27 MoldWorks2006 User Guide A - Socket head angle. hrough hole on . • The Through Thread check box will cause the hole to be a t the final part Add Component 8 -28 MoldWorks2006. will cause the hole to be a through hole on the final part. Add Component 8 -26 MoldWorks2006 User Guide w 8. 12 Countersunk Scre Create a countersunk screw and countersunk screw hole(s) through